RAY

Sort By:  
Raytronic C50 DC Balance Charger - 500W / (2x250W) (3EC1050)
Small two-channel charger Raytronic C50 2×250W designed to offer a smart charging with high power and simple and intuitive operation.
Raytronic C50 allows to charge and discharge common types of batteries (NiCD, NiMH, LiPo, LiFe, LiHV, Li-Ion, Pb) and is also equipped with 6-channel balance port for safe charging of lithium batteries.
The charger has a coloured LCD display and programming button and dial.

Features

Program for new types of "High Voltage" lithium (LiHV) batteries with an output charging voltage up to 4.25V
Powerful balance with current up to 800mA
Optional synchronised operation of both channels for charging a single battery with power up to 500W
Optional recuperative discharging with high power when charging from a car battery (energy consumed by the charger is used to charge the car battery powering the charger again)
Adjustable output voltage for charging and discharging lithium batteries.
Programs for charging intelligent batteries for popular DJI drones.

Parameters overview

Input: 7.28V DC (XT60 connector)
For charging/discharging 1–16cell NiCd/NiMH, 1–6cell Li-Ion/LiPo/LiFe/LiHV or 2–20V Pb batteries
Adjustable charging current (0.1–15.0 A) for each channel
Adjustable discharging current (0.1–3.0 A), or recuperative discharging (0.1–15.0 A) for each channel
Charging power output up to 2x250W / 1x500W for synchronous charging
Discharging power output up to 2x12W, up to 2x250W for recuperative discharging
Charging finishing via automatic "Delta-Peak" for NiCd and NiMH batteries
Lithium and Pb batteries are charged via the "constant current/constant voltage" method
Adjustable sensitivity of "Delta-Peak" detection for NiCd/NiMH batteries
Adjustable output voltage for charging and discharging the lithium batteries
Repeated cyclic charging/discharging or discharging/charging operation for NiCd and NiMH batteries, up to 12 cycles
3 lithium battery modes - charging, discharging and charging/discharging for storing (all of this with a balance port or without it).
Finishing of charging after reaching a set time, temperature or supplied charge
Memory for 5 charging/discharging programs
Internal resistance measuring for individual cells
Stabilised DC current source (0.1–15.0 A) with an adjustable voltage limit
Charging programs for intelligent DJI Mavic/Phantom/Inspire batteries
Ports for temperature sensor (sold separately)
USB input (5V / 2.1A) for smartphone/tablets/other charging
Simple firmware update via USB port
Backlit coloured LCD display with simple and well-arranged menu, parameter overview during charging/discharging
Programming button and dial for simple and intuitive setting and controlling the charger
Warning messages for higher safety - incorrect input voltage, incorrect connection, unsuitable battery or its condition, incorrect polarity etc.,..
Incorrect polarity and on-input short-circuit protection
Forced-cooling fan
Compact plastic body with very small dimensions

Both channels are equipped with an output XT60 ports and universal ports for service connectors JST-XH, allowing direct connection of battery power cables and service connectors JST-XH for 2–6S packs. If you are using a pack with XT60 and JST-XH connects (no additional cables needed).

Note: charger uses output voltage of 2.4V/cell for Pb battery charging. It is suitable for charging typical lead-acid batteries (car batteries) and gel batteries with reversible valve.
NOT SUITABLE for charging gas-tight gel batteries charged with a maximum of 2.3V/cell.

Package contains:
Raytronic C50 Charger
USB Cable
Screen Protector
User Manual

69.54€  Inc Tax
Ray 5AA (RX) Receiver Pack - NiMh 6.0V 2000mAh Battery (JR) (7BA1050905K)
  • Raytronic rechargeable receiver battery pack 5AA
  • NiMh 6.0V 2000mAh (JR connector)
  • Hump pack
  • 125g


14.64€  Inc Tax
Raytronic P40 Power Supply 30V / 40A - 1000W (3EC1127)
Switched-mode stabilized 1000W power supply with adjustable output voltage 13–30V for 230/50Hz. Voltage and current are shown on an LED display. Double output terminals for 4mm banana connectors.

High power stabilized power supply Raytronic P40 can supply up to 1000W to the DC battery chargers other devices that need 13–30V DC power.

It is equipped with overload and short circuit protection. The power supply has an active cooling system, that stabilizes operation and protect from overheating.

Output voltage is set via rotary knob on a front panel. Values of output voltage or current are shown on 3-digit LED display (Voltage and Current are switch selectable).

Output banana connector terminals are doubled, so you can easily connect two chargers or other devices when needed. Combined power output of up to 1000W.

Set includes:
Raytronic P40 power supply
Power cable
User manual

149.45€  Inc Tax
RAY Propeller Adapter (M6) 5mm (3EA0190)
RAY Propeller Adapter (M6) 5mm

4.27€  Inc Tax
Per Page      1 - 4 of 4
  • 1