Futaba

Sort By:  
Futaba R2008SB 2.4GHz S-FHSS 8 channel S.Bus Receiver (FUT5102613)
Futaba R2008SB 2.4GHz S-FHSS 8 Channel S.Bus Receiver

The R2008SB 2.4GHz S-FHSS receiver is S.Bus-compatible and features Dual Antenna Diversity. It also comes equipped to handle high voltage applications.

Features:
High-voltage operation
Frequency-hopping Spread Spectrum design
Dual Antenna Diversity
S.Bus compatible

Specifications:
Type: Full-range flight receiver
Modes: S-FHSS or FHSS
Voltage Input: 4.8V-7.4V battery or regulated output from ESC
Compatible Batteries: NiCd, NiMH, LiPo, LiIon or LiFe
Dimensions: 24.9x42.8x14.0mm
Weight: 9.5g

52.46€  Inc Tax
Futaba R3106GF T-FHSS 6 Channel Receiver (mono) (FUT5102641)
The Futaba R3106GF was developed alongside the Futaba T6L radio system and offers the best value for money of all of the Futaba receivers.

The R3106GF uses Futaba's T-FHSS Air Mono system so it works with all T-FHSS aircraft transmitters from the top of the range T18MZWC to the entry level T6L. The 'Mono' name means that this receiver does not include a telemetry downlink, this simplifies the receiver helping to keep the price down for applications where telemetry is simply not needed.

The receiver itself is surrounded by a hard plastic two piece case to give it the maximum protection and makes it easy to install.
The servo plugs are vertical for easy access and there is a LED indicator to show the bind status.
The aerial is 145mm long so you can easily mount the 30mm tip in a secure place.

• 6 Channels
• High Voltage Capable (4.8 - 7.4V)
• T-FHSS Air Mono System (As used by T6L)
• Tough moulded plastic case
• Simple button free easy pairing
• Weight just under 8g

32.94€  Inc Tax
Futaba R7008SB FASSTest 8ch + S.BUS 2.4GHz Receiver (FUT5102556)
The Futaba R7000SB is a FASSTest telemetry enabled receiver, a high-voltage design that operates up to 8 channels using the 8 standard PWM outputs or up to 18 channels (16 proportional + 2 digital) using the S-Bus port.

High-Voltage Receiver for the Futaba 18MZ, 18SZ,14SG Radio System

That means a simpler setup and full support for S-Bus and S-Bus2 servos. As supplied the R7008SB receiver includes integral sensors for receiver voltage, signal strength and external voltage, with further sensors available separately.

8 Channel using PWM
18 Channel using S.Bus
Extra voltage port (0 - 70V DC)
Diversity aerial for optimal reception
S.Bus & S.Bus2 capability
High Voltage capable

Specifications:
Fail Safe: Yes
Modulation: FASSTest (18ch & 12ch Modes)
S.BUS: S.Bus & S.Bus2
Weight: 10.9g
Current Drain: 75mA
Channels: 8 PWM (18 S-BUS)
Dimensions: 24.9x47.3x14.3mm
Voltage: 3.7 - 7.4V (3.5 - 8.4V voltage range)

119.56€  Inc Tax
Futaba S.BUS Telemetry HUB (30cm, 3-port) (FUT0074)
Futaba S.BUS / S.BUS2 Telemetry HUB

Features:
3-port splitter
30cm extension cable
Three-core cable with power supply from S-BUS / S.BUS2 connector

33.55€  Inc Tax
Futaba 3PV 3(+1) Channel 2.4GHz T-FHSS Telemetry Transmitter w/R304SB Receiver (FUT5003109)
Futaba 3PV T-FHSS Telemetry Radio System is sophisticated, powerful and easy to use. It offers a super-fast response rate that can make a difference on a race day. With FHSS, S-FHSS and T-FHSS protocols Futaba 3PV is one of the R/C's most versatile surface radio control system.

Features:
FHSS/S-FHSS/T-FHSS protocols
10 Model Memory
4-Character Model Name
Low Battery Alarm
Steering Trim
Throttle Trim
Channel 4 Trim
Sub Trim
Steering Dual Rates
Steering End Point Adjustment
Throttle End Point Adjustment
Channel 3 End Point Adjustment
Channel 4 End Point Adjustment
Mixing (4WS,Brake)
Steering Servo Reversing
Throttle Servo Reversing
Channel 3 Servo Reversing
Channel 4 Servo Reversing
Steering Exponential (changes sensitivity around neutral servo point)
Throttle Exponential (sensitivity of the throttle servo)
Throttle Fail Safe
ABS Function
Model data can be copied to another model
Auto Power-Off after 10 minutes

Futaba 3PV Transmitter Specifications:
Type: 3(+1)* Channel FHSS/S-FHSS/T-FHSS
*The 4th channel is used for mixing functions only.
Requires: 4x AA alkaline batteries / or 6.6V LiFe battery / or 6V NiMH Battery

Comes with R304SB 4-Channel 2.4GHz T-FHSS Telemetry S.BUS2 Receiver

Features:
T-FHSS system, S.BUS2, 4-channel receiver
Dimensions: 35.1x23.2x8.5mm
Weight: 6.6g
Rated Voltage: 4.8 to 7.4V / Usable Voltage: 3.5 to 8.4V
Number of Ports: 5
Number of PWM Output: 4
Telemetry: Yes (T-FHSS)
Telemetry: Collect as many telemetry sensors by HUB and connect them to S.BUS2 port
Range: Full Range Receiver

136.64€  Inc Tax
Futaba 3PV 3(+1) Channel 2.4GHz T-FHSS Telemetry Transmitter w/R203GF Receiver (FUT5003108)
Futaba 3PV T-FHSS Telemetry Radio System is sophisticated, powerful and easy to use. It offers a super-fast response rate that can make a difference on a race day. With FHSS, S-FHSS and T-FHSS protocols Futaba 3PV is one of the R/C's most versatile surface radio control system.

Features:
FHSS/S-FHSS/T-FHSS protocols
10 Model Memory
4-Character Model Name
Low Battery Alarm
Steering Trim
Throttle Trim
Channel 4 Trim
Sub Trim
Steering Dual Rates
Steering End Point Adjustment
Throttle End Point Adjustment
Channel 3 End Point Adjustment
Channel 4 End Point Adjustment
Mixing (4WS,Brake)
Steering Servo Reversing
Throttle Servo Reversing
Channel 3 Servo Reversing
Channel 4 Servo Reversing
Steering Exponential (changes sensitivity around neutral servo point)
Throttle Exponential (sensitivity of the throttle servo)
Throttle Fail Safe
ABS Function
Model data can be copied to another model
Auto Power-Off after 10 minutes

Note: T-FHSS is available only with T-FHSS capable receivers.

Futaba 3PV Transmitter Specifications:
Type: 3(+1)* Channel FHSS/S-FHSS/T-FHSS
*The 4th channel is used for mixing functions only.
Requires: 4x AA alkaline batteries / or 6.6V LiFe battery / or 6V NiMH Battery

Comes with R203GF 3-Channel 2.4GHz FHSS Receiver

Features: 
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 26x39x10mm
Weight: 8g
Operating Voltage: 4.8 to 7.4V
Number of Ports: 4
PWM Output: 3
S-FHSS: Yes
Range: Full Range

114.68€  Inc Tax
Futaba 3PRKA 2.4GHz FHSS Transmitter w/R203GF Receiver (FUT5003049)
Futaba 3PRKA 3-Channel Digital Proportional 2.4GHz FHSS RC Radio System. Economically priced system that that comes with may features. Great for drivers starting out and for drivers who want to upgrade the radio in their (RTR) ready-to-run model. 

Features:
Throttle and Steering Trim with a Reverse Function
Throttle End Point Adjustment
Steering Dual Rate
Switched third channel
Throttle Fail Safe
70:30 Throttle Mode
Built-in antenna
Low battery warning

Comes with R203GF 3-Channel 2.4GHz FHSS Receiver

Features: 
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 26x39x10mm
Weight: 8g
Operating Voltage: 4.8 to 7.4V
Number of Ports: 4
PWM Output: 3
S-FHSS: Yes
Range: Full Range

74.42€  Inc Tax
Futaba S.BUS Telemetry HUB (10cm, 3-port) (FUT0073)
Futaba S.BUS / S.BUS2 Telemetry HUB

Features:
3-port splitter
10cm extension cable
Three-core cable with power supply from S-BUS / S.BUS2 connector

31.72€  Inc Tax
Futaba R2104GF S-FHSS/FHSS 4-Channel Receiver (FUT5102507)
The Futaba R2104GF 4-Channel 2.4GHz S-FHSS Receiver is compatible with Futaba FHSS and S-FHSS transmitters.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest systems. It will work with FHSS and T-FHSS transmitters, but transmitter mode has to be changed from T-FHSS/FHSS to S-FHSS mode.

Features:
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 39x26x10mm
Weight: 8g
Operating Voltage: 4.8 or 6V
Number of Ports: 5
PWM Output: 4
S-FHSS: Yes

58.56€  Inc Tax
Futaba R304SB-E T-FHSS 4-Channel Telemetry Receiver (EP Cars/Rock Crawlers) (FUT5102601)
The Futaba R304SB-E 2.4GHz T-FHSS 4-Channel Telemetry Enabled Receiver is only compatible with Futaba T-FHSS telemetry compatible transmitters.

Built-in antenna
The R304SB-E receiver is designed to be used only for Electric Powered Car models. Due to the special design of the receiver, we cannot recommend its use in other types of models (gas powered models). Ideally sized to fit in 1/8, 1/10 or 1/12 on-road and offroad electric powered RC cars and rock crawlers.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest, FHSS or S-FHSS systems.

Features:
T-FHSS system, S.BUS2, 4-channel receiver
Dimensions: 35.1x23.2x12.5mm
Weight: 6.7g
Rated Voltage: 4.8 to 7.4V / Usable Voltage: 3.5 to 8.4V
Number of Ports: 5
Number of PWM Output: 4
Telemetry: Yes (T-FHSS)
Telemetry: Collect as many telemetry sensors by HUB and connect them to S.BUS2 port
Range: Full Range Receiver (70m @ the best condition)

49.90€  Inc Tax
Futaba R304SB T-FHSS 4-Channel Telemetry Receiver (FUT5102611)
The Futaba R304SB 2.4GHz T-FHSS 4-Channel Telemetry Enabled Receiver is only compatible with Futaba T-FHSS telemetry compatible transmitters.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest, FHSS or S-FHSS systems.

Features:
T-FHSS system, S.BUS2, 4-channel receiver
Dimensions: 35.1x23.2x8.5mm
Weight: 6.6g
Rated Voltage: 4.8 to 7.4V / Usable Voltage: 3.5 to 8.4V
Number of Ports: 5
Number of PWM Output: 4
Telemetry: Yes (T-FHSS)
Telemetry: Collect as many telemetry sensors by HUB and connect them to S.BUS2 port
Range: Full Range Receiver

39.65€  Inc Tax
Futaba R202GF S-FHSS/FHSS 2-Channel Receiver (FUT5102625)
The Futaba R202GF 2.4GHz S-FHSS 2-Channel Micro Receiver is compatible with Futaba FHSS and S-FHSS transmitters.

It is a simple surface receiver with a single external aerial for easy installation and can use a battery power supply (4.8-7.4V) using the spare battery port. Comes with a simple bind button and a LED indicator for the status. It is a perfect fit to radio controlled cars, boats and other surface vehicles.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest systems. It will work with FHSS and T-FHSS transmitters, but transmitter mode has to be changed from T-FHSS/FHSS to S-FHSS mode.

Features:
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 23x35x9mm
Weight: 6g
Operating Voltage: 4.8 to 7.4V
Number of Ports: 3
Number of Channel: 2
S-FHSS: Yes

29.89€  Inc Tax
Futaba R203GF S-FHSS/FHSS 3-Channel Receiver (FUT5102519)
The Futaba R203GF 3-Channel 2.4GHz S-FHSS Receiver is compatible with Futaba FHSS and S-FHSS transmitters.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest systems. It will work with FHSS and T-FHSS transmitters, but transmitter mode has to be changed from T-FHSS/FHSS to S-FHSS mode.

Features:
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 26x39x10mm
Weight: 8g
Operating Voltage: 4.8 to 7.4V
Number of Ports: 4
PWM Output: 3
S-FHSS: Yes
Range: Full Range

39.65€  Inc Tax
Futaba R204GF-E S-FHSS/FHSS 4-Channel Receiver (EP Cars/Rock Crawlers) (FUT5102555)
The Futaba R204GF-E 2.4GHz S-FHSS 4-Channel Micro Receiver is compatible with Futaba FHSS and S-FHSS transmitters.

Built-in antenna
The R204GF-E receiver is designed to be used only for Electric Powered Car models. Due to the special design of the receiver, we cannot recommend its use in other types of models (gas powered models). Ideally sized to fit 1/10 or 1/12 on-road electric powered RC cars and rock crawlers.

Frequency Hopping Spread Spectrum (FHSS) technology minimizes interference from other 2.4GHz systems. Easy Link prevents unwanted signal conflicts by using a special, pre-assigned ID code.

Note: NOT compatible with 2.4GHz FASST or FASSTest systems. It will work with FHSS and T-FHSS transmitters, but transmitter mode has to be changed from T-FHSS/FHSS to S-FHSS mode.

Features:
S-FHSS/FHSS auto detection
Compatible with Futaba S-FHSS/FHSS protocol
Dimensions: 35.1x23.2x9mm
Weight: 6g
Operating Voltage: 4.8 to 7.4V
Number of Ports: 4
Number of Channel: 4
S-FHSS: Yes
Range: Full Range (70m @ the best conditions)

46.97€  Inc Tax
Futaba R3008SB 2.4GHz 8ch T-FHSS + S.BUS Receiver (FUT5102609)
Futaba R3008SB 2.4GHz 8ch T-FHSS + S.BUS 2 Receiver

The new and full range Futaba R3008SB receiver is designed to be used with the equally new 10J transmitter, and has 8 conventional outputs, or a full 10 through the S-Bus or S-Bus 2 outputs, whilst of course a mix is also possible by using 7 or 8 conventional servos and 2 or 3 S-Bus or S-Bus2 servos, or even additional conventional servos via an SBD decoder lead. The extremely compact dimensions of only 47.3 x 24.8 x 14.6 (max) and end connectors make this the perfect receiver for almost all applications, ranging from power models through helicopters and gliders.

Specifications:
Modulation: 2.4GHz T-FHSS
S-BUS2 Port for telemetry
Diversity Dual Antenna
Weight: 7.5g
Voltage: 3.5 - 8.4v
Channels: 8+ S.Bus 2 port
Dimensions: 47.3x24.8x14.6mm

59.78€  Inc Tax
Futaba External Voltage Cable (FUT0141)
Futaba CA-RVIN-700 External Voltage Sensor Cable

CA-RVIN-700 cable for sensing external voltage (flt pack) in the range of 0 - 70V.
Only for compatible telemetry receivers with special port (R3008SB, R7008SB, R7014SB, R7108SB).

15.25€  Inc Tax
Futaba R3004SB 2.4GHz 4ch T-FHSS + S.BUS Receiver (FUT5102653)
The Futaba R3004SB is a slim 4-channel receiver that is ideally suited to smaller models, as well as gliders/electric gliders that still require full range transmission. Futaba ditched bulky moulded cases and opted for lightweight heat shrink instead, this provides protection for almost any use but helps keep the weight down to just under 5 grams. The electronics are uncompromised, so the R3004SB has full telemetry features and full range transmission. It's slim and compact format makes it ideal for almost any application, whilst a pair of coaxial aerials provide solid stable reception with their length allowing them to be positioned at 90 degrees from each other, to give the maximum possible range.

2.4GHz T-FHSS Air system
4 Channels + S-BUS
S-BUS2 Port for telemetry
Diversity Dual Antenna
Ultra small design for smaller models
Heat shrink enclosure to reduce weight

Specification:
Modulation: T-FHSS Air
Weight: 4.8g
Voltage: 4.8 - 7.4V
Channels: 4ch + S.Bus2 Port
Dimensions: 18x41.4x9.9mm
Frequency: 2.4GHz
Aerial Length: 2x 150mm

45.75€  Inc Tax
Per Page      1 - 17 of 17
  • 1