RadioLink

Sort By:  
RadioLink T8FB Remote Controller (FHSS) with R8EF 8ch receiver (1RL0030)
RadioLink T8FB Remote Controller (FHSS) with R8EF 8ch receiver

Features:
Custom designed firmware for helicopter, fixed wing airplane, glider, multi-copter and other radio controlled models.
Online upgrades available through the simulator port and special Radiolink upgrade cable (no need for drivers and compatible with all OS).
T8FB simplifies the operation and makes it intuitevly easy to use even without reading detailed instruction manual.
Follows the technology of wireless spread spectrum for better control.
S-BUS, PPM and PWM signal output at the same time

T8FB Specification:
Size: T8FB - 173x102x206mm
Weight: 0.47kg
Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)
Modulation mode: GFSK
Channel bandwidth: 400KHz
Band width:1200KHz
Spread spectrum: FHSS
Adjacent channel rejection: >36dBM
PWM output: 1.0ms~2.0ms
Cycle:15 ms/per frame
Radio T8FB operating voltage: 4.8V~18V
Radio T8FB operating current: <110mA
Control distance: more than 1000 meters in the air (the actual control distance depends on the flying environment)

R8EF Receiver:
Channel: 8ch
Operating voltage: 4.8-10V
Operating current: 19-25mA (input voltage 5V)
Size: 48.5x21x11mm
Weight: 7g
Section precision: 4096
Signal output: S-BUS, PPM and PWM
Signal mode: Green LED, output 8 channel PWM signal
SBUS/PPM signal mode: Both red and green LED on, CH1 output S-BUS signal, CH2 output PPM signal, CH3 to CH8 output PWM signal (at the same time)

Package Including:
1x T8FB 2.4G 8CH Remote Control System Transmitter
1x R8EF Receiver

59.78€  Inc Tax
RadioLink R8EF 8ch 2.4GHz FHSS Receiver (S-BUS+PPM) (1RL0046)
RadioLink R8EF 8ch 2.4GHz FHSS Receiver

R8EF Receiver:
Channel: 8ch
Operating voltage: 4.9-10V
Operating current: 19-25mA (input voltage 5V)
Size: 48.5x21x11mm
Weight: 7g
Feature: Fail-safe
Section precision: 4096
Signal output: S-BUS, PPM and PWM
Signal mode: Green LED, output 8 channel PWM signal
SBUS/PPM signal mode: Both red and green LED on, CH1 output S-BUS signal, CH2 output PPM signal, CH3 to CH8 output PWM signal (at the same time)

Package Including:
1x R8EF Receiver

18.91€  Inc Tax
RadioLink R6DS 6ch 2.4GHz FHSS Receiver (S-BUS+PPM) (1RL0040)
Radiolink R6DS 2.4GHz 6ch PPM/PWM/S-BUS Output Receiver

The R6DS is a small 6 channel S-BUS / PPM / PWM ready receiver from Radiolink with three signal outputs.
The R6DS can output both PWM and S.BUS output simultaneously.

PWM output: 6 channels totally
S.BUS output
PPM output: CH1 outputs PPM signal for 10 channels, and channel 2 to channel 6 output independent PWM signal simultaneously

All channels have a response time of 3 ms. Specially designed for small models and light drones
Compatible with most flight controllers such as DJI NAZA, ZERO TECH, PIX, APM, MINI APM, NAZE32, and CC3D, etc.,..
A single cable needed for flight controller connection. With its miniature size and a total weight of 3.9 grams, the R6DSD is a great choice for light models and drones.

Specification:
Brand Name: Radiolink
Item Name: R6DS
Band: 2.4G
Channel: 6 (Red LED indicator is for PWM mode. Blue LED for PPM, It can be extended to 10channels)
Power Input: 4.8 - 6V
Control Distance: 600m in air
Current Consumption: 38-45mA (Input voltage:5V)
Dimension: 25×16×11mm
Weight: 3.9g
Precision: 4096

Features:
DSSS&FHSS transmission.
Output SBUS, PPM and PWM signals simultaneously.
Top speed response, 3ms for all channels parallel.
Top precision 4096
Sub miniature size, totally weights 3.4 grams
All channels response parallel, totally 3ms.
One single cable connect with the flight controller, easy setting

Receiver Operation:
SBUS/PPM and PWM signal change

Short press the ID SET switch two times within 1 second, the signal is changed from normal PWM to SBUS/PPM. The red LED indicates the normal PWM and blue/purple indicates SBUS/PPM.

Installment of receiver antenna
The antenna must be kept as straight as possible. Otherwise it will reduce the effective range.
Large model aircraft may of some metal part interfering signal; in this case the antennas should be placed at both sides of the model. Then the best RF signal condition is obtained at any flying attitude.
The antennas must be kept away from conductive materials, such as metal and carbon by at least a half inch. The coaxial part of the antennas does not need to follow these guidelines, but do not bend it in a small radius.
Keep the antennas away from the motor, ESC, and other noise sources as much as possible.
Press and hold the Easy Link (ID SET) one second, now the receiver starts work.
After all of the above steps finished, the LED indicator will turn and keep in red.
The receiver can be packed by sponge or foam for shocking proof when it is installed to the model.

Package Includes:
1x Radiolink R6DS receiver

15.86€  Inc Tax
Per Page      1 - 3 of 3
  • 1