Slovenščina RC Electronics
AWG 14 silicone cable with 4mm gold (banana) connector - XT90 (male)
Use this adaptor / charging cable for charging the batteries for radio controlled (RC) airplanes, helicopters, cars, trucks, buggies, boats and other models and model accessories.
FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.
Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"
The engine set includes:
FOXY G3 C2826-750 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.
Engine Mounting:
The FOXY G3 C2826-750 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.
The marking according to the engine dimensions: C3548; The marking according to the stator dimensions: C2826
Specifications:
No. of (LiXX) cells: 3-5
Motor Kv: 750 rpm/V
Max power (30s/5S Lipo): 580W
No-load current (3S): 2.1A
Max peak current (30s): 42A
Diameter: 35mm
Length: 50.7mm
Shaft diameter: 5mm
Weight: 172g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 50-60A
Application:
Gliders up to: 2700g
Trainers up to: 2600g
Acro planes up to: 2300g
3D airplanes up to: 1500g
Recommended propellers:
4S: 13X6,5”
5S: 11X6”
Length: 25.4mm
Internal Thread: M3
Servo spline: 25T
Servo arm / control horn for use in radio controlled (RC) airplanes and and other models.
Product Description
This is a universal mount designed to accept almost any micro servo. The top of the mount features an aerodynamic fairing designed to streamline airflow around the servo linkage.
Specifications:
Diameter (mm): 50
Thickness (mm): 14
Thickness with the fairing (mm): 28
Use this wing servo mount (servo mounting bracket) for radio controlled (RC) airplanes, gliders, hotliners, and other models.
Conductor cross-section 0.25 mm2
External dimensions 1.5x4.8 mm
Max. 48 V, 5A.
Package: 10 meters
Flat extension lead / cable without connectors.
Use for radio controlled (RC) model airplanes, helicopters, cars, trucks, buggies, boats and other applications.
XT60 (female) and EC5 (male) connector / AWG 14 cables
Use this adaptor cable for charging the batteries for radio controlled (RC) airplanes, helicopters, cars, trucks, buggies, boats and other models.
Packaging: 5 plugs and 5 sockets (10 pcs / female and male XT60 connectors)
Use this connectors for radio controlled (RC) airplanes, helicopters, cars, trucks, buggies, boats and other models
Packaging: 10 pcs
Use this connectors for radio controlled (RC) airplanes, helicopters, cars, trucks, buggies, boats and other models
The cable connects the mz-12 PRO, mz-16, mz-32, mc-26 and mc-28 radios to the Android Smartphone without the need for a Bluetooth device.
This cable is an excellent addition when using the Smartphone holder to connect the phone and radio.
Use this accessory for radio controlled (RC) airplanes, helicopters, drones and other models.
Use this accessory for radio controlled (RC) airplanes, helicopters and other models.
Hand-wound EGODRIFT Tengu 4035HT F3C Edition motor for training and competition with a rating of 540kV. The Special F3C Edition has ben developed, tested and refined together with the best Japanese pilots, incl. World Championship contestant Masatoshi Iso.
Offering precise and linear response for smooth, controlled operation in any 750-760 sized F3C radio controlled helicopter (heli) model such as the: Goblin Urukay, Quest Impaction, Align T-Rex 760, Prodrone PDH-02C, Hirobo Eagle 4, RVE Merak E750, XLPower E-Wraith and others.
Like all models within the Tengu series, the top of the can features the iconic and heat-resistant EGODRIFT Stickerbomb design, to add the finishing touch to your f3c heli build.
Each motor comes with mounting screws and an (optional) screw for additional securing of the bell.
SPECIFICATIONS
Manufacturer: EGODRIFT
Stator size: 4035
Motor configuration: 12N10P
Motor weight: 480g
Base Colour: Black
Wire colour: Copper
Motor wire type: High temperature copper wire
Motor wire: 1.3mm
Motor shaft: Hardened Steel
LiPo cells: 12S
Motor kV: 540 kV
Stator diameter: 40 mm
Stator height: 35 mm
Stator lamination: 0.15 mm (+)
Body Length: 60mm (2.36 inch)
Diameter: 49.6mm
Screw hole diameter: 3,0 mm
Motor hole pattern: 25mm, 30mm
Idle current: 4.0A
Maximum Current: 110A (128A Peak / 2 seconds)
Maximum Power: 4840W (Peak: 5632W / 2 seconds)
Internal resistance: 28 mOhm
Connection: Wire / Gold plated plugs
Designer: Yutao Zou
Length: 36mm
Internal Thread: M3
Servo spline: 25T
Servo arm / control horn for use in radio controlled (RC) airplanes, boats, cars and and other models.
Real-time Telemetry
Real-time model data feedback allows users to receive crucial information on the model's systems.
When paired with flight module PRM-01, model voltage is displayed.
Configurable sound/message/vibration alarms signal potential problems when low model voltage. A low model voltage alarm value can be customized.
Real-time Model Voltage Telemetry Module
Model: PRM-01
Dimensions: 33 x 22 x 11mm
Weight (with wire): 7g
Voltage Input Range: 1S - 6S LiPo Battery
Compatible receiver: R12DS, R9DS (Old version receiver: R10DS, R10D, R9D)
Compatible transmitter: AT10II/AT10/AT9S Pro/AT9S/AT9
Configurable sound/message/vibration alarms signal for low voltage (customizable).
Package Including:
1x Real-time Model Voltage Telemetry Module PRM-01
4mm Gold Connectors (male) and Traxxas (male)
Connectors: 4mm gold connectors stepped to 5mm
XT60 (female) and EC5 (male)
Radiolink R8FM, 2.4G 8 channel receiver support SBUS and PPM signal
Good choice for use with Radiolink T8FB transmitter in a racing drone.
2000 Meters Control Distance
67-channel pseudo-random frequency hopping help reduce overall signal interference.
2000 meters range enables all possible RC fun.
The maximum PWM jitter is 1.84us with a standard of just 0.5us.
SBUS or PPM Signal Output
8 channels of SBUS/PPM signal output.
Compatible with PIXHWAK, MINI PIX, TURBO PIX, and APM flight controllers which support SBUS or PPM signal.
Weight of 2.5g and small size of 16.0 x 21.5 x 1.0mm make R8FM is tiny enough even for mini racing drone and glider
R8EF Receiver:
Channel: 8ch
Operating voltage: 3 - 6V
Operating current: 38-45mA (input voltage 5V)
Size: 48.5x21x11mm
Weight: 2.5g
Section precision: 4096, 0.25us per section
Signal output: SBUS, PPM
Control distance: 2000 meters in the air
Compatible transmitter: T8S /T8FB/ RC6GS V2/ RC4GS V2/ RC6GS/ RC4GS
Package Including:
1x R8FM Receiver
2.4GHz T-FHSS Air system
4 Channels + S-BUS
S-BUS2 Port for telemetry
Diversity Dual Antenna
Ultra small design for smaller models
Heat shrink enclosure to reduce weight
Specification:
Modulation: T-FHSS Air
Weight: 4.8g
Voltage: 4.8 - 7.4V
Channels: 4ch + S.Bus2 Port
Dimensions: 18x41.4x9.9mm
Frequency: 2.4GHz
Aerial Length: 2x 150mm
R8EF Receiver:
Channel: 8ch
Operating voltage: 4.9-10V
Operating current: 19-25mA (input voltage 5V)
Size: 48.5x21x11mm
Weight: 7g
Feature: Fail-safe
Section precision: 4096
Signal output: S-BUS, PPM and PWM
Signal mode: Green LED, output 8 channel PWM signal
SBUS/PPM signal mode: Both red and green LED on, CH1 output S-BUS signal, CH2 output PPM signal, CH3 to CH8 output PWM signal (at the same time)
Package Including:
1x R8EF Receiver
Built for most demanding pocket charger
Converts standard household power 100-240V AC to 24V DC power and supply up to 16 amperes of continuous power.
Safer and Reliable
- Short-circuit protection on output
- Over Current Protection
- Over Temperature Protection
- Over Load Protection
- Over Voltage Protection
Active PFC
Active PFC is the use of power electronics to change the waveform of current drawn by a load to improve the power factor, thus achieving the purpose of higher efficiency. Active PFC, which is integrated into SkyRC 380W/16A regulated power supply, can provide higher power utilization.
Intelligent Air Cooling System
Adopting the cooling system, the fan will be initiated automatically when operating temperature reaches 50 degree.
Overload/Error Indication
The LED indicator turn red whenever equipment connected to the Power Supply is drawing more power than it can provide. The Power Supply may shut down turning off its output in order to protect its circuitry from damage.
Rigorous testing, derived from the pursuit of quality
Each 380W power supply must experience dozens of more than the industry standard of critical testing. Each rigorous testing and every detailing are the reflections of SkyRC's concentration on products.
Specification
Converts standard household power 100-240V AC to 24V DC power and supply up to 16 amperes of continuous power.
Size and Weight
Case Size：165x139x59.5mm
Weight：1.11kg
Power Supply
Voltage：100-240V
Input AC Frequency：50-60Hz
Output Current：16A
Output Voltage：24V DC±0.5V
Output Voltage Ripple：<300mV
Power Efficiency：88%
Power Factor：>0.98
Protection
Current Overload Protection：17A ±1A
Over Temperature Protection：<80℃
Cooling Method: Cooling Fan
Operating Temperature：0-40℃
Operating Humidity：0-90%
Key Features
- Case design offers better strain relief on antenna lead
- DSMX with DSM2 Backward compatibility*
- 22ms and 11ms Compatible
- Upgrade for any Spektrum receiver with available remote receiver ports
- Great addition to AR636, AR7350, AR9350, Telemetry Receivers and PowerSafe receivers
- Includes 24 inch extension
Repositionable Antenna
This antenna design allows for easy repositioning with the option to exit the case from the side or top. It also offers added strain relief to the antenna wire, and is optimized to fit into the tightest of Remote control aircraft.
Overview
The next generation of Spektrum remote receivers are here with the SPM9745 and SPM9746 Receivers. Featuring a user friendly antenna setup that allows for the antenna to be placed in 2 positions, making installation into those tight projects easier than ever. Fully compatible with DSMX and DSM2 Transmitters*. Use these to add more receiving points on any Spektrum receiver that has 1 or more Remote receiver ports.
The remote receiver includes one 24-inch extension; however, various lengths of receiver extensions can be purchased allowing various placement options for mounting purposes. Additional remote receiver extensions are available in 6", 9", 12", 24" and 36" lengths.
*DSMX Remote Receivers must be used with a DSMX Main Receiver.
Kyosho SYNCRO KT231P+ (TX) Surface Transmitter + KR331 (RX) 3-channel Surface Receiver
KST X15-755X HV Digital Coreless Servo Motor (metal gear)
The KST X15-755X HV Brushless servo offers a significantly longer life-span, with a superior power to weight ratio. The servo features a nicely machined aluminium case and offerers high voltage capability. It can be run directly from a 2S LiPo battery without the need for a separate voltage regulator.
Another great benefit of X15 servos is the all new design of a circuit board that generates no counter EMF in any working conditions. It eliminates any possible interference with your flybarless system or receiver unit thus as a result giving you only the best in-flight performance.
Due to the extreme reliability and performance this servos are used in film and motion picture industry as well as in robotics, drones, UAV, UAS, academic researches, and other highly demanding applications such as use in various military projects,..
Technical Details:
Voltage (max.) [V]: 8.4
Torque [kg/cm]@6.0V: 7.2
Torque [kg/cm]@7.4V: 9.0
Torque [kg/cm]@8.4V: 10.2
Speed [s/60°]@6.0V: 0.06
Speed [s/60°]@7.4V: 0.05
Speed [s/60°]@8.4V: 0.04
Width [mm]: 15.0
Length [mm]: 35.5
Height [mm]: 32.5
Weight [g]: 40.0
Motor typ: Coreless
Working Frequency: 760us/560Hz, 450us-1050us
Resolution: <2us
Gear: Hardened Steel
Ball Bearing: 2BB
Output shaft type: 25T
Servo size: Mini
Waterproof: No
Manufacturer: KST
Suitable for use as s Tail Servo on 320-580 size RC Helicopters;
Such as Goblin 380 420, 500, KRAKEN 580, T-REX 450PRO DFC, 450L, 470, 500, Mikado LOGO 480, 500, OXY 5, and similar,..
KST X12-508 HV Digital Coreless Servo Motor (metal gear)
The KST X12-508 HV Brushless servo offers a significantly longer life-span, with a superior power to weight ratio. The servo features a nicely machined aluminium case and offerers high voltage capability. It can be run directly from a 2S LiPo battery without the need for a separate voltage regulator.
Another great benefit of X12 servos is the all new design of a circuit board that generates no counter EMF in any working conditions. It eliminates any possible interference with your flybarless system or receiver unit thus as a result giving you only the best in-flight performance.
Due to the extreme reliability and performance this servos are used in film and motion picture industry as well as in robotics, drones, UAV, UAS, academic researches, and other highly demanding applications such as use in various military projects,..
Technical Details:
Voltage (max.) [V]: 8.4
Torque [kg/cm]@6.0V: 4.2
Torque [kg/cm]@7.4V: 5.2
Torque [kg/cm]@8.4V: 6.2
Speed [s/60°]@6.0V: 0.09
Speed [s/60°]@7.4V: 0.08
Speed [s/60°]@8.4V: 0.07
Width [mm]: 12.0
Length [mm]: 23.0
Height [mm]: 27.5
Weight [g]: 20.0
Motor typ: Coreless
Working Frequency: 1520us/333Hz, 900us-2100us
Resolution: <2us
Gear: Metal Gear
Ball Bearing: 2BB
Output shaft type: 25T
Servo size: Micro
Waterproof: No
Manufacturer: KST
Suitable for Swashplate use on 250-470 size RC helicopters;
Such as Oxy 3, Goblin 280 Fireball, 380, 420, T-REX 250, 300, 450, 470, MSH PROTOS 380, and similars,..
This multifunction program box is for programming HobbyWing brushless ESCs. Its friendly LCD interface makes ESC programming easy and quick. With a PC, you can upgrade ESC firmware and further adjust ESC parameters online. Besides, it’s compact, portable and very applicable for field use.
This multifunction LCD program box is applicable for the following HobbyWing products:
Platinum series of brushless aircraft ESCs, XeRun series &EzRun series of brushless car ESCs, Seaking Pro series of brushless boat ESCs
Specifications
Size：91x51x17mm（LxWxH）
Weight：65g
Input Voltage: 4.5V—12.6V (a separate battery is needed for powering this program box when ESC has no built-in/external BEC)
Interface: Micro USB， ESC interface (Futaba plug), Power supply interface (Futaba plug)
RPM sensor for backplate installation on 40- to 90-sized glow engines
Bolt-on installation with nothing else to install, picks up the rotation of the crankshaft through the backplate
Compatible with Spektrum™ telemetry modules
Has a micro JST connector and plugs into the TM1000 telemetry module
TM1000 AND/OR a Telemetry Capable Transmitter required