Electric Motors

Sort By:  
FOXY G3 Brushless Motor C2206-1500kv (3BL2610)
FOXY G3 C2206-1500

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

FOXY G3 C2206-1500 is a miniature brushless motor designed to drive small models with a flight weight of up to 300 g, powered by a 2 or 3-cell Li-po battery. With this motor you can successfully "electrify" rubber bands from Guillow's or Dumas kits with a span of up to approx. 1200 mm, it is also excellent for park-flyers and indoor aerobatic models.

Engine mounting:
The FOXY G3 C2206-1500 is designed for rear mounting with a propeller mounted using a rubber band. Use at least two (opposite) or four M2 screws for mounting. The fastening cross is part of the engine.

Engine set includes:
FOXY G3 C2206-1500 engine with cables and instruction manual.

The marking according to the engine dimensions: C2824; The marking according to the stator dimensions: C2206

Specifications:
No. of (LiXX) cells: 2-3
Motor Kv: 1500 rpm/V
Max power (30s/3S Lipo): 100W
No-load current (2S): 0.4A
Max peak current (30s): 12A
Diameter: 27.8mm
Length: 26mm
Shaft diameter: 3.175mm
Weight: 42g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 15-20A

Application:
Gliders up to: 300g
Trainers up to: 280g
Acro planes up to: 250g
3D airplanes up to: 200g

Recommended propellers:
2S: 9X5”
3S: 7X3,5”

17.69€  Inc Tax
FOXY G3 Brushless Motor C2216-850kv (3BL2650)
FOXY G3 C2816-850

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2816-850 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2816-850 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C2836; The marking according to the stator dimensions: C2216

Specifications:
No. of (LiXX) cells: 2-4
Motor Kv: 850 rpm/V
Max power (30s/4S Lipo): 200W
No-load current (2S): 0.8A
Max peak current (30s): 18A
Diameter: 27.8mm
Length: 34mm
Shaft diameter: 4mm
Weight: 76g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 30-35A

Application:
Gliders up to: 1050g
Trainers up to: 900g
Acro planes up to: 800g
3D airplanes up to: 600g

Recommended propellers:
3S: 11X5”
4S: 9X5”

23.79€  Inc Tax
Graupner Motor ESC Prop Set A (CCW) (GRFT4523)
Graupner ULTRA MOTOR 2804 2300kv CCW
Graupner Ultra Control BlHeli 20A 7.2-17.4V SBEC
Propeller Graupner Sport Prop 5x3 (2 pieces)

Motor specification:
Operating Voltage Range: 2-4S
Number of poles: 14
Shaft Diameter: 5mm
Case Diameter: 28mm
Kv (RPM/V): 2300
Recommended propeller: 5-6"


29.89€  Inc Tax
FOXY G3 Brushless Motor C2208-1000kv (3BL2615)
FOXY G3 C2208-1000

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2208-1000 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2208-1000 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C2826; The marking according to the stator dimensions: C2208

Specifications:
No. of (LiXX) cells: 2-3
Motor Kv: 1000 rpm/V
Max power (30s/3S Lipo): 120W
No-load current (2S): 0.4A
Max peak current (30s): 14A
Diameter: 27.8mm
Length: 28mm
Shaft diameter: 3.175mm
Weight: 51g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 18-20A

Application:
Gliders up to: 450g
Trainers up to: 450g
Acro planes up to: 400g
3D airplanes up to: 330g

Recommended propellers:
2S: 10X5”
3S: 9X5”

19.52€  Inc Tax
FOXY G3 Brushless Motor C3520-880kv (3BL2715)
FOXY G3 C3520-880

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C3520-880 brushless motor with 4mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C3520-880 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C4050; The marking according to the stator dimensions: C3520

Specifications:
No. of (LiXX) cells: 3-5
Motor Kv: 880 rpm/V
Max power (30s/5S Lipo): 880W
No-load current (4S): 4.5A
Max peak current (30s): 63A
Diameter: 42.8mm
Length: 50mm
Shaft diameter: 5mm
Weight: 230g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 70-80A

Application:
Gliders up to: 3000g
Trainers up to: 3000g
Acro planes up to: 2500g
3D airplanes up to: 1800g

Recommended propellers:
3S: 14X7-8”
4S: 13X6”
5S: 11X6-7”

39.65€  Inc Tax
FOXY G3 Brushless Motor C2826-750kv (3BL2700)
FOXY G3 C2826-750

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2826-750 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2826-750 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3548; The marking according to the stator dimensions: C2826

Specifications:
No. of (LiXX) cells: 3-5
Motor Kv: 750 rpm/V
Max power (30s/5S Lipo): 580W
No-load current (3S): 2.1A
Max peak current (30s): 42A
Diameter: 35mm
Length: 50.7mm
Shaft diameter: 5mm
Weight: 172g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 50-60A

Application:
Gliders up to: 2700g
Trainers up to: 2600g
Acro planes up to: 2300g
3D airplanes up to: 1500g

Recommended propellers:
4S: 13X6,5”
5S: 11X6”

34.16€  Inc Tax
FOXY G3 Brushless Motor C2826-500kv (3BL2695)
FOXY G3 C2826-500

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2826-500 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2826-500 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3548; The marking according to the stator dimensions: C2826

Specifications:
No. of (LiXX) cells: 3-6
Motor Kv: 500 rpm/V
Max power (30s/6S Lipo): 600W
No-load current (3S): 1.6A
Max peak current (30s): 36A
Diameter: 35mm
Length: 50.7mm
Shaft diameter: 5mm
Weight: 172g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 45-50A

Application:
Gliders up to: 2800g
Trainers up to: 2700g
Acro planes up to: 2300g
3D airplanes up to: 1500g

Recommended propellers:
6S: 13X6,5”

34.16€  Inc Tax
Graupner Motor ESC Prop Set B (CCW) (GRFT4524)
Graupner ULTRA MOTOR 2812 1200kv CCW
Graupner Ultra Control BlHeli 35A 7.2-17.4V SBEC
Propeller Graupner Sport Prop 8x4.5 (2 pieces)

Motor pecification:
Operating Voltage Range: 2-6S
Number of poles: 14
Shaft Diameter: 5mm
Case Diameter: 28mm
Case Length: 24mm
Overall Length: 43mm
Kv (RPM/V): 1200
Recommended propeller: 8-10"
Weight (inc. spinner and 2mm connectors): 53g

31.72€  Inc Tax
FOXY G3 Brushless Motor C2808-1500kv (3BL2660)
FOXY G3 C2808-1500

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2808-1500 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2808-1500 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3530; The marking according to the stator dimensions: C2808

Specifications:
No. of (LiXX) cells: 2-4
Motor Kv: 1500 rpm/V
Max power (30s/4S Lipo): 370W
No-load current (2S): 1.7A
Max peak current (30s): 33A
Diameter: 35mm
Length: 30mm
Shaft diameter: 4mm
Weight: 90g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 40-45A

Application:
Gliders up to: 950g
Trainers up to: 900g
Acro planes up to: 800g
3D airplanes up to: 700g

Recommended propellers:
3S: 9X5”
4S: 7X6”

26.23€  Inc Tax
FOXY G3 Brushless Motor C2820-950kv (3BL2690)
FOXY G3 C2820-950

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2820-950 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2820-950 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3542; The marking according to the stator dimensions: C2820

Specifications:
No. of (LiXX) cells: 3-4
Motor Kv: 950 rpm/V
Max power (30s/4S Lipo): 500W
No-load current (3S): 1.7A
Max peak current (30s): 45A
Diameter: 35mm
Length: 44.7mm
Shaft diameter: 4mm
Weight: 142g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 50-60A

Application:
Gliders up to: 2400g
Trainers up to: 2300g
Acro planes up to: 2000g
3D airplanes up to: 1500g

Recommended propellers:
3S: 13X6,5”
4S: 11X5,5”

29.89€  Inc Tax
Graupner ULTRA 2806 2300KV Brushless Motor CW (S7049)
Graupner ULTRA Race copter MOTOR 2300kv CW

Specification:
Operating Voltage Range: 7.4-11.1V (2-3S)
Number of poles: 14
Shaft Diameter: 5mm
Case Diameter: 28mm
Case Length: 18.7mm
Kv (RPM/V): 2300
Weight (inc. spinner and 2mm connectors): 33.5g

9.76€  Inc Tax
Graupner ULTRA 2806 2300KV Brushless Motor CCW (S7050)
Graupner ULTRA Race copter MOTOR 2300kv CCW

Specification:
Operating Voltage Range: 7.4-11.1V (2-3S)
Number of poles: 14
Shaft Diameter: 5mm
Case Diameter: 28mm
Case Length: 18.7mm
Kv (RPM/V): 2300
Weight (inc. spinner and 2mm connectors): 33.5g

9.76€  Inc Tax
EGODRIFT Tengu 2520HS / 3560KV (3S) (ED11795)
Hand-wound EGODRIFT Tengu 2520HS motor for 450 class rc helicopter models with a kV rating of 3560kV - intended for use with 3S LiPo batteries.

EGODRIFT Tengu high-performance brushless motors for RC heli are the result of one year of testing and development. The 2520HS comes with a kV rating of 3560kV for 3S LiPo batteries and is the perfect choice for your 450 sized helicopter model.

Like all models within the Tengu series, the top of the can features the iconic and heat-resistant EGODRIFT Stickerbomb print, to add the finishing touch to your 450 class heli build.

Each motor comes with mounting screws and 3 pairs of gold bullet connectors.

SPECIFICATIONS
Manufacturer: EGODRIFT
Stator size: 2520
Motor configuration: 12N10P
Motor weight: 108g
Base Colour: Black
Wire colour: Copper
Motor wire type: High temperature copper wire
Motor wire: 0.45mm
Motor shaft: Hardened Steel
Shaft diameter: 3.5 mm
External shaft length (mm): 17 mm
LiPo cells: 3S
Motor kV: 3560 kV
Stator diameter: 25 mm
Stator height: 20 mm
Stator lamination: 0.15 mm (+)
Body Length: 37.30mm
Diameter: 32.70mm
Screw hole diameter: 3,0 mm
Motor hole pattern: 16 mm, 19 mm
Idle current: 5.4A
Maximum Current: 50.8A (Peak: 70.2A / 2 seconds)
Maximum Power: 762 W (Peak: 1053W / 2 seconds)
Internal resistance: 8 mOhm
Connection: Wire / Gold plated plugs
Designer: Yutao Zou

96.99€  Inc Tax
EGODRIFT Tengu 4035HT / 540KV F3C Edition (12S) (ED11829)
Hand-wound EGODRIFT Tengu 4035HT F3C Edition motor for training and competition with a rating of 540kV. The Special F3C Edition has ben developed, tested and refined together with the best Japanese pilots, incl. World Championship contestant Masatoshi Iso. Offering precise and linear response for smooth, controlled operation in any 750-760 sized F3C heli model such as the: Goblin Urukay, Quest Impaction, Align T-Rex 760, Prodrone PDH-02C, Hirobo Eagle 4, RVE Merak E750, XLPower E-Wraith and alike.

Hand-wound EGODRIFT Tengu 4035HT F3C Edition motor for training and competition with a rating of 540kV. The Special F3C Edition has ben developed, tested and refined together with the best Japanese pilots, incl. World Championship contestant Masatoshi Iso.

Offering precise and linear response for smooth, controlled operation in any 750-760 sized F3C radio controlled helicopter (heli) model such as the: Goblin Urukay, Quest Impaction, Align T-Rex 760, Prodrone PDH-02C, Hirobo Eagle 4, RVE Merak E750, XLPower E-Wraith and others.

Like all models within the Tengu series, the top of the can features the iconic and heat-resistant EGODRIFT Stickerbomb design, to add the finishing touch to your f3c heli build.

Each motor comes with mounting screws and an (optional) screw for additional securing of the bell.

SPECIFICATIONS
Manufacturer: EGODRIFT
Stator size: 4035
Motor configuration: 12N10P
Motor weight: 480g
Base Colour: Black
Wire colour: Copper
Motor wire type: High temperature copper wire
Motor wire: 1.3mm
Motor shaft: Hardened Steel
LiPo cells: 12S
Motor kV: 540 kV
Stator diameter: 40 mm
Stator height: 35 mm
Stator lamination: 0.15 mm (+)
Body Length: 60mm (2.36 inch)
Diameter: 49.6mm
Screw hole diameter: 3,0 mm
Motor hole pattern: 25mm, 30mm
Idle current: 4.0A
Maximum Current: 110A (128A Peak / 2 seconds)
Maximum Power: 4840W (Peak: 5632W / 2 seconds)
Internal resistance: 28 mOhm
Connection: Wire / Gold plated plugs
Designer: Yutao Zou

344.65€  Inc Tax
Graupner Motor ESC Prop Set F (CCW) (GRFT4526)
Graupner ULTRA MOTOR 2806 1900kv CCW
Graupner Ultra Control BlHeli 20A 7.2-17.4V SBEC
Propeller Graupner Sport Prop 6x3 (2 pieces)

Motor pecification:
Operating Voltage Range: 2-4S
Number of poles: 14
Shaft Diameter: 5mm
Case Diameter: 28mm
Case Length: 18mm
Overall Length: 37mm
Kv (RPM/V): 1900
Recommended propeller: 5-6"
Weight (inc. spinner and 2mm connectors): 34g

28.06€  Inc Tax
FOXY G3 Brushless Motor C2814-1000kv (3BL2665)
FOXY G3 C2814-1000

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2814-1000 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2814-1000 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3536; The marking according to the stator dimensions: C2814

Specifications:
No. of (LiXX) cells: 3-4
Motor Kv: 1000 rpm/V
Max power (30s/4S Lipo): 370W
No-load current (3S): 1.3A
Max peak current (30s): 38A
Diameter: 35mm
Length: 38.7mm
Shaft diameter: 4mm
Weight: 115g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 40-45A

Application:
Gliders up to: 1700g
Trainers up to: 1600g
Acro planes up to: 1330g
3D airplanes up to: 1050g

Recommended propellers:
3S: 12X6”
4S: 10X5”

27.45€  Inc Tax
FOXY G2 Brushless motor C4125-400kv (3BL1745)
FOXY G2 C4125-400

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G2 C4125-400 brushless motor with gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G2 C4125-400 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the stator dimensions: C4125

Specifications:
No. of (LiXX) cells: 4-8
Motor Kv: 400 rpm/V
Motor Wind: 8 Turns
Max power (180s): 1550W
Motor resistance: 32mOhm
No-load current (Io/10v): 1.5A
Current at maximum efficiency (η>80%): 10 - 38A
Max peak current (180s): 70A
Diameter: 49.5mm
Length: 54mm
Shaft diameter: 6mm
Weight: 332g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 90-120A

Application:
Gliders up to: 4500g
Trainers up to: 4000g
Acro planes up to: 3600g
3D airplanes up to: 3000g
 
Recommended propellers:
6S: 15X8-10”
8S: 13X6.5”

74.42€  Inc Tax
FOXY G3 Brushless Motor C3530-700kv (3BL2725)
FOXY G3 C3530-700

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C3530-700 brushless motor with 4mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C3530-700 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C4060; The marking according to the stator dimensions: C3530

Specifications:
No. of (LiXX) cells: 3-6
Motor Kv: 700 rpm/V
Max power (30s/6S Lipo): 1150W
No-load current (4S): 5.5A
Max peak current (30s): 69A
Diameter: 42.8mm
Length: 60mm
Shaft diameter: 6mm
Weight: 295g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 80-90A

Application:
Gliders up to: 3500g
Trainers up to: 3300g
Acro planes up to: 2800g
3D airplanes up to: 2200g

Recommended propellers:
4S: 15X8-10”
5S: 13X8”
6S: 12X6”

46.97€  Inc Tax
FOXY G3 Brushless Motor C3520-730kv (3BL2710)
FOXY G3 C3520-730

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C3520-730 brushless motor with 4mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C3520-730 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C4050; The marking according to the stator dimensions: C3520

Specifications:
No. of (LiXX) cells: 3-6
Motor Kv: 730 rpm/V
Max power (30s/5S Lipo): 810W
No-load current (4S): 3.6A
Max peak current (30s): 58A
Diameter: 42.8mm
Length: 50mm
Shaft diameter: 5mm
Weight: 230g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 65-80A

Application:
Gliders up to: 3000g
Trainers up to: 3000g
Acro planes up to: 2500g
3D airplanes up to: 1800g

Recommended propellers:
5S: 13X6-8”
6S: 12X6”

39.65€  Inc Tax
FOXY G3 Brushless Motor C2808-1200kv (3BL2655)
FOXY G3 C2808-1200

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2808-1200 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2808-1200 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C3530; The marking according to the stator dimensions: C2808

Specifications:
No. of (LiXX) cells: 2-4
Motor Kv: 1200 rpm/V
Max power (30s/4S Lipo): 300W
No-load current (2S): 0.9A
Max peak current (30s): 27A
Diameter: 35mm
Length: 30mm
Shaft diameter: 4mm
Weight: 90g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 35-40A

Application:
Gliders up to: 1200g
Trainers up to: 1000g
Acro planes up to: 850g
3D airplanes up to: 750g

Recommended propellers:
3S: 10X5”
4S: 8X5”

26.23€  Inc Tax
FOXY G3 Brushless Motor C2212-1100kv (3BL2630)
FOXY G3 C2212-1100

FOXY brushless motors are 14-pole rotary casing electric motors with excellent electrical properties featuring a very sophisticated design and high-end manufacturing. Hardened steel shafts and high-quality bearings ensure a long service life, while the quality of materials used to make the stator on the rotor also guarantees excellent performance at a high efficiency. They are low-speed, high-torque engines that handle large diameter propellers and pitches without the need for gearboxes.

Engine marking system: CxxYY / zzzz
C - brushless motor ("outrunner", "circular")
xx - stator diameter in mm
YY - stator length in mm
zzzz - revolutions per volt (rpm/V), "KV"

The engine set includes:
FOXY G3 C2212-1100 brushless motor with 3.5mm gold-plated connectors, rear and front mounting kit and an instruction manual.

Engine Mounting:
The FOXY G3 C2212-1100 is designed for both front and rear mounting. For front mounting at the front of the motor use at least two (opposite) or four bolts. The rear mounting kit (mounting cross, tail propeller) is also supplied with the engine.

The marking according to the engine dimensions: C2830; The marking according to the stator dimensions: C2212

Specifications:
No. of (LiXX) cells: 2-3
Motor Kv: 1100 rpm/V
Max power (30s/3S Lipo): 180W
No-load current (2S): 1.1A
Max peak current (30s): 21A
Diameter: 27.8mm
Length: 32mm
Shaft diameter: 3.175mm
Weight: 62g
Magnet poles: 14
Motor timing: 15-25deg
Regulator: 20-25A

Application:
Gliders up to: 800g
Trainers up to: 700g
Acro planes up to: 600g
3D airplanes up to: 400g

Recommended propellers:
3S: 9X5”

20.13€  Inc Tax
Hobbywing Seaking 3660SL Brushless Motor for Boats 2-4S 3180kV (HW90070030)
Hobbywing Seaking 3660SL Brushless Motor for Boats 2-4S 3180kV

The Seaking Brushless motors are high-quality electric motors of the most popular performance classes. High-quality CNC milled aluminum components impress with concentric precision and finely-balanced components. Together with the neodymium magnets and the double ball bearings, these motors have a very high running stability. They are water cooled through a push on cooling sleeve and sealed by two O-rings. The winding is made of high-quality copper for the highest efficiency and to keep the thermal resistance at minimum levels.

Features:
High torque
High-quality neodymium magnets
Water cooled
Double ball bearing
High-speed bearings
Precision made and balanced parts
CNC milled high quality aluminum parts
Replacement O-rings included

Specification:
Motor ID: 3660SL
Pole: 4
LiPo:2-4S
kV: 3060
Max Current (A) / Max Vol (V): 94A/16.8V
No Load Current (A) @ 7.4V: 2.7A
Resistance: 0.0058
Diameter: 36mm
Diameter of water cooling pipe: Ф5mm
Length (without shaft): 60mm
Shaft Diameter: 5mm
Shaft Length: 16mm
Weight: 240g

99.43€  Inc Tax
Hobbywing Seaking 2848SL Brushless Motor for Boats 2-3S 3900kV (HW90070010)
Hobbywing Seaking 2848SL Brushless Motor for Boats 2-3S 3900kV

The Seaking Brushless motors are high-quality electric motors of the most popular performance classes. High-quality CNC milled aluminum components impress with concentric precision and finely-balanced components. Together with the neodymium magnets and the double ball bearings, these motors have a very high running stability. They are water cooled through a push on cooling sleeve and sealed by two O-rings. The winding is made of high-quality copper for the highest efficiency and to keep the thermal resistance at minimum levels.

Features:
High torque
High-quality neodymium magnets
Water cooled
Double ball bearing
High-speed bearings
Precision made and balanced parts
CNC milled high quality aluminum parts
Replacement O-rings included

Specification:
Motor ID: 2848SL
Pole: 2
LiPo:2-3S
kV: 3900
Max Current (A) / Max Vol (V): 41A/12.6V
No Load Current (A) @ 7.4V: 2.4A
Resistance: 0.0155
Diameter: 27.8mm
Diameter of water cooling pipe: Ф5mm
Length (without shaft): 48mm
Shaft Diameter: 3.175mm
Shaft Length: 12mm
Weight: 135g

69.54€  Inc Tax
Hobbywing Seaking 2040SL Brushless Motor for Boats 2-3S 4800kV (HW90070000)
Hobbywing Seaking 2040SL Brushless Motor for Boats 2-3S 4800kV

The Seaking Brushless motors are high-quality electric motors of the most popular performance classes. High-quality CNC milled aluminum components impress with concentric precision and finely-balanced components. Together with the neodymium magnets and the double ball bearings, these motors have a very high running stability. They are water cooled through a push on cooling sleeve and sealed by two O-rings. The winding is made of high-quality copper for the highest efficiency and to keep the thermal resistance at minimum levels.

Features:
High torque
High-quality neodymium magnets
Water cooled
Double ball bearing
High-speed bearings
Precision made and balanced parts
CNC milled high quality aluminum parts
Replacement O-rings included

Specification:
Motor ID: 2040SL
Pole: 2
LiPo:2-3S
kV: 4800
Max Current (A) / Max Vol (V): 20A/12.6V
No Load Current (A) @ 7.4V: 1.8A
Resistance: 0.0399
Diameter: 20mm
Diameter of water cooling pipe: Ф4mm
Length (without shaft): 40mm
Shaft Diameter: 2.3mm
Shaft Length: 12.5mm
Weight: 60g

42.70€  Inc Tax
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 5400kV (3.175mm) for 1:10 (HW30402602)
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 5400kV (3.175mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3652SL-5400KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 5400 kV
LiPo Cells: 2S
No-load Current: 7.2A
Resistance: 5.1mΩ
Outer Diameter: 36mm
Length: 52mm
Shaft Diameter: 3.175mm
Weight: 217g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 15mm
Application: 1/10th Scale Touring Car/Buggy (Sport), SCT (2WD), Monster Truck/Truck (Light-duty)

54.90€  Inc Tax
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 4000kV (3.175mm) for 1:10 (HW30402601)
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 4000kV (3.175mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3652SL-4000KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 4000 kV
LiPo Cells: 2-3S
No-load Current: 5.2A
Resistance: 7.4mΩ
Outer Diameter: 36mm
Length: 52mm
Shaft Diameter: 3.175mm
Weight: 216g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 15mm
Application: 1/10th Scale Touring Car/Buggy (Sport), SCT (2WD), Monster Truck/Truck (Light-duty)

54.90€  Inc Tax
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 3300kV (3.175mm) for 1:10 (HW30402600)
Hobbywing EzRun 3652SL (Sensorless) Brushless Motor G2 3300kV (3.175mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3652SL-3300KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 3300 kV
LiPo Cells: 2-3S
No-load Current: 4.3A
Resistance: 10.0mΩ
Outer Diameter: 36mm
Length: 52mm
Shaft Diameter: 3.175mm
Weight: 218g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 15mm
Application: 1/10th Scale Touring Car/Buggy (Sport), SCT (2WD), Monster Truck/Truck (Light-duty)

54.90€  Inc Tax
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 4600kV (5mm) for 1:10 (HW30402652)
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 4600kV (5mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3660SL-4600KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 4600 kV
LiPo Cells: 2S
No-load Current: 7.2A
Resistance: 5.3mΩ
Outer Diameter: 36mm
Length: 60mm
Shaft Diameter: 5mm
Weight: 262g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 18.5mm
Application: 1/10th Scale SCT (4WD), Monster Truck, Truck (Heavy-duty)

74.42€  Inc Tax
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 4000kV (5mm) for 1:10 (HW30402651)
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 4000kV (5mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3660SL-4000KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 4000 kV
LiPo Cells: 2-3S
No-load Current: 5.7A
Resistance: 6.0mΩ
Outer Diameter: 36mm
Length: 60mm
Shaft Diameter: 5mm
Weight: 268g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 18.5mm
Application: 1/10th Scale SCT (4WD), Monster Truck, Truck (Heavy-duty)

74.42€  Inc Tax
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 3200kV (5mm) for 1:10 (HW30402650)
Hobbywing EzRun 3660SL (Sensorless) Brushless Motor G2 3200kV (5mm shaft) for 1:10

High Torque
The 4 pole design will guarantee the motor to produce very large amounts of torque, a much faster acceleration response and a very stable output of power to the drivetrain.

Low Cogging Torque
The first motor adopted the innovative 4-pole-8-magnet "staggered pole" rotor (Hobbywing-patented design) in the RC field has the extremely low cogging effect and low torque pulsation (it's reduced by 85% when comparing with conventional 1/10th scale 4-pole motors).

Motor Thermal Protection
When pairing the EzRun 3652/3660 G2 with a Hobbywing EzRun MAX10-SCT or MAX10 ESC, the built-in temperature sensor and sensor port at the load end (for connecting to ESC) will make the motor thermal protection available to protect the motor from damage due to overheat.

Excellent Design
The O-ring seals fitted between the front end bell and motor case isolates screw holes from inner parts to prevent liquid or dust from getting inside and protect motor from damage. The special design of the motor case isolates inner coils from outside to protect winding from being damaged by overlong screws.

High Efficiency
Hobbywing’s temperature control technology has been designed to protect the motor from being damaged by heat thus less heat more efficient the motor will run and perform. The output performance of this motor has an efficiency rate of up to 90%, a leading level in the RC world.

Build Quality
The use of double insulated windings (240℃ R-leveled), high-intensity adhesive (340℃), Japanese bearings and silicon steel sheets guarantees users the outstanding performance and super durability. The wheel hub design of the front & rear end bells reduces the motor weight.

EzRun MAX10-SCT/MAX10 ESC
When pairing the EzRun 3652/3660 G2 motor with a Hobbwing EzRun MAX10-SCT/ MAX10 ESC, the excellent match between ESC and motor will give you large torque plus a very smooth and linear power band.

Specification:
Product name: EZRUN-3660SL-3200KV-G2
Scale: 1/10th
Brushless: Yes
Sensored: No
Pole Count: 4
Rating: 3200 kV
LiPo Cells: 2-3S
No-load Current: 4.9A
Resistance: 8.3mΩ
Outer Diameter: 36mm
Length: 60mm
Shaft Diameter: 5mm
Weight: 262g
Front Bearing: D5xD13xt4
Rear Bearing: D5xD13xt4
Shaft Length: 18.5mm
Application: 1/10th Scale SCT (4WD), Monster Truck, Truck (Heavy-duty)

74.42€  Inc Tax
Per Page      1 - 30 of 35